DP-FsE series
Corrosion-resistant Non-metallic Specification! Safe Design with Intrinsically Explosion-proof Specification.
A non-metallic model diaphragm pump that uses resin as the material even for the main parts, and employs a fiber-optic stroke sensor control model of the DP-Fs series.
Even if the one-piece diaphragm is damaged, metal ion contamination is prevented, and the pump can be operated with peace of mind in a corrosive environment, so it is suitable for CMP slurry transfer.
■ Main Applications
Transfer of Flammable Liquids in Explosion-proof Areas/Transfer of Chemicals, Pure Water, and Waste Liquids
Features
■ Seal Specification
| Hard Seal Supports expansion and contraction of the resin due to the heat cycle, and is resistant to temperature changes. |
|
|
■ Non-Metallic Specification
| One-piece Diaphragm Center disk less diaphragm with integrated center disk and diaphragm. Replacement is extremely simple, and it has excellent running costs. |
Resin Center Rod By using resin as the center rod material, non-metal is achieved. |
|
|
|
■ Employs Fiber-optic Stroke Sensor Control.
Employs a fiber-optic stroke sensor control model that can be used even in explosion-proof areas.
◆ Sensor Control “Fiber-Optic Stroke Sensor”
| Non-metal, Explosion-proof Model By including a fiber-optic stroke sensor, the pump can be used in explosion-proof areas. |
|
|
| Sensor Control = Stable Reciprocating Motion A proximity sensor detects the stroke end of the diaphragm, and the pump controller receiving the sensor signal controls the switching of the center exhaust type 3-position 5-port solenoid valve. |
| Optional Counter Connection Enables Stroke Management By counting the number of times the center rod has moved, it is possible to determine when parts need to be replaced. |
|
|
Specifications
| Valve Shape and Model Number | |||||
| Ball Valve |
DP-10FsE |
DP-10FsE |
DP-20FsE |
DP-20FsE |
|
| Body Material | |||||
| Center Body | Polypropylene (PPG) | ||||
| Pump Body | PTFE | ||||
| Wetted Parts Material | |||||
| Diaphragm PTFE | PTFE | ||||
| Valve PTFE | |||||
| Valve Seat PTFE | |||||
| Valve Stopper PTFE |
|||||
| Center Disk PFA | Integrated with diaphragm | ||||
| Specifications | |||||
| Nominal Diameter | 3/8" (10 mm) | 3/4" (20 mm) | |||
| Material Connection |
Suction Port | Rc 3/8 (F) | JIS flange 10K 10A equivalent |
Rc 3/4 (F) | JIS flange 10K 20A equivalent |
| Discharge Port | |||||
| Air Connection |
Supply Port | Rc 1/4 x 2 (Shared supply and exhaust port x 2) *1 | |||
| Exhaust Port | |||||
| Air Supply Pressure | 0.2~0.5 MPa *2 | ||||
| Maximum Discharge Pressure | 0.5 MPa | ||||
| Water Discharge/Cycle |
60 mL *3 | 180 mL *3 | |||
| Maximum Flow Rate | 20 L/min | 45 L/min | |||
| Maximum Air Consumption | 350 L/min (ANR) | 450 L/min (ANR) | |||
| Maximum Size Solid | Maximum 1 mm | Maximum 2 mm | |||
| Viscosity Limit | Maximum 1 Pa·s | Maximum 2 Pa·s | |||
| Temp Range |
Ambient | 0~70 °C | |||
| Liquid Temperature | 0~80 °C | ||||
| Noise Level | 80 dB | 82 dB | |||
| Net Weight | 11.3 kg | 18.6 kg | |||
*1 The pipe length from the air supply valve (solenoid valve, etc.) to the pump shall be 1.5 m or less. If piping from the exhaust port of the air supply valve to another location, the pipe length to the end of the exhaust port shall be 5 m or less.
*2 The compressed air quality shall satisfy quality classes both 2 and 3 specified in “JIS B8392-1:2000 Compressed air for general use.”
(Maximum particle diameter: 1 μm, Maximum open air pressure: －20°C, Maximum oil concentration: 0.1 mg/m3)
The maximum supply air pressure of a type with a resin-made pump body depends on the liquid temperature.
*3 The water discharge is provided as a rough approximation only. The discharge will differ depending on factors such as the liquid to be transferred and the piping conditions.